Item Type: Stepper Motor Driver_x000D_ Product Model: DMA860H_x000D_ Output Current (A): 2.4-7.2_x000D_ Input Power Supply Voltage (VAC): 18-80_x000D_ Control Signal Input Current (mA): 7-20_x000D_ Step Pulse Frequency (KHz): 0-200_x000D_ Insulation Resistance (M): 500_x000D_ Main Application Areas: _x000D_ Suitable for all kinds of medium and large automation equipment, such as engraving machines, cutting machines, packaging machinery, electronic processing equipment, automatic assembly equipment, etc., the application effect is particularly good in the equipment where users expect low noise and high speed_x000D_ Instructions: _x000D_ 1. Micro-step Subdivision Setting: The micro-step subdivision number of the driver is set by the four DIP switches SW5-SW8. There are 16 levels of micro-step subdivision. When the user sets micro-step subdivision, the driver should be stopped first. For the specific microstep setting, please read the driver layout description_x000D_ 2. Output Current Setting: The output current of the driver is set by three DIP switches SW1-SW3. There are 8 levels of output current. For specific output current settings, please read the driver's layout description._x000D_ 3. Automatic Half-flow Function: The user can set the automatic half-flow function of the drive through SW4. off means that the quiescent current is set to half of the dynamic current, on means that the quiescent current is the same as the dynamic current. In general use, SW4 should be set to off, so that the heating of the motor and the driver is reduced, and the reliability is improved. About 0.4 seconds after the pulse stops, the current is automatically reduced to about half (60% of the actual value), and the calorific value is theoretically reduced to 36%_x000D_ 4. Signal Interface: PUL+ and PUL- are the positive and negative ends of the control pulse signal; DIR+ and DIR- are the positive and negative ends of the direction signal; ENA+ and ENA- are the positive and negative ends of the enable signal_x000D_ 5. Motor Interface: A+ and A- are connected to the positive and negative ends of the A-phase winding of the stepping motor; B+ and B- are connected to the positive and negative ends of the B-phase winding of the stepping motor. When the A and B phase windings are exchanged, the direction of the motor can be reversed_x000D_ 6. Power Interface: AC or DC power supply is used, the working voltage range of DMA860H is recommended to be 48-75VAC, and the power supply is greater than 500W_x000D_ 7. Indicator Light: The drive has two indicator lights, red and green. The green light is the power indicator, the green light is always on when the drive is powered on; the red light is the fault indicator, and the fault light is always on when an overvoltage or overcurrent fault occurs. After the fault is cleared, the red light is off. When the drive fails, only re-power on and re-enable to clear the fault_x000D_ 8. Installation Instructions: _x000D_ The External size of The Drive Are: Approx. 151 x 97 x 51mm / 5.9 x 3.8 x 2in_x000D_ Installation Hole Distance: Approx. 139mm / 5.5in_x000D_ It can be installed horizontally and vertically, and it is recommended to install it vertically. When installing, it should be close to the metal cabinet to facilitate heat dissipation._x000D_ Size: Approx. 97mm / 3.8in_x000D_ 143mm / 5.6in_x000D_ 151mm / 5.9in_x000D_ _x000D_ 23.5mm / 0.9in_x000D_ 45.5mm / 1.8in_x000D_ 4mm / 0.2in_x000D_ _x000D_ 139mm / 5.5in_x000D_ 4.5mm / 0.2in_x000D_ 48mm / 1.9in_x000D_ _x000D_ 10.5mm / 0.4in