Industrial Control Board PLC Regulator FX1N-20MR Programmable Logic Controller 24V DC

Features:_x000D__x000D_This programmable logic controller uses industrial-grade 32-bit MCU with strong anti-interference and faster speed. _x000D_High quality chip, stable performance, on-line download, on-line monitoring, automatic save when power off. _x000D_Program is written in ladder logic programming language, supports for GX-Developer, GX-work2. _x000D_Programming port is the port for program upload, download, test and monitor. _x000D_It is reusable, stable, easy to learn. The PLC transmission baud rate is 9600. _x000D__x000D_Specifications:_x000D_Model: FX1N-20mr_x000D_Working Voltage: DC24V_x000D_Wide Power Supply Voltage: 10-28VDC_x000D_Baud Rate: 9600_x000D_Programming Software: for GX-Developer, for GX-work2._x000D_Size: Approx. 86 x 73 x 20mm / 3.4 x 2.9 x 0.7inch_x000D_Weight: 120G_x000D__x000D_Package Included:_x000D_1 x PLC Board_x000D__x000D_Chinese programming software download address:Pan.baidu.com/s/1nty5XXn_x000D_PLC data download address: Pan.baidu.com/s/1eRNhn3O_x000D__x000D_Module function:_x000D_This module is programmable control, can achieve thousands of functions, stable and reliable working performance, built-in watchdog timer circuit, to ensure that the module for a long time to run!!!_x000D_Some of the common features are shown as follows:_x000D__x000D_Turn on the power supply, the relay 1 is closed for N seconds and then disconnect the relay 2 for N seconds. _x000D_When the power supply is turned on, the relay 1 is switched off after N seconds, and then the relay 2 is closed for N seconds and then is turned off. _x000D_The power supply is switched on, the relay 1, 2 have no action, when a signal or trigger button, relay 1 closed off after N seconds; then relay 2 closed off after N seconds, until the next trigger, repeat the same action. _x000D_Through the signal 1, 2 programming, the control can be achieved on the relay 1 and 2 arbitrarily. _x000D_When the signal 1 has a signal, the relay 1 is closed, the relay 2 is disconnected; when the signal 2 has a signal, the relay 1 is turned off, and the relay 2 is closed. _x000D_Can be connected to the NPN sensor signal, the sensor signal programming, to achieve arbitrary control of the relay. _x000D_When the signal 1 is triggered, the relay 1 is controlled, and when the signal 2 is triggered, the relay 2 is controlled. _x000D_Turn on the power supply, the control motor is turning N seconds, and then reverse N seconds, followed by the cycle. _x000D_When the signal 1 has a signal, the motor is controlled to rotate; when the signal 2 has a signal, the motor is reversed. _x000D__x000D_These are just some examples, modules can achieve far more than these functions_x000D__x000D_Input high speed pulse C235, C251 and FX1N compatible. _x000D_Output relay 1A output, Rated current 5A, can directly drive DC solenoid valve, AC solenoid valve, AC contactor, AC motor, etc,. _x000D__x000D_Precautions for use:_x000D__x000D_The PLC with two programming port. The 232 interface, you can directly use the USB-232 serial port with a computer to download the program directly. The TTL interface. _x000D_Built-in Analog input AD, corresponding to internal data register D5030.(Not D8030) _x000D_Built-in Analog output DA, corresponding to internal data register D5101. _x000D_When the PLC need to connect with the touch screen or text, can be used to connect 232 programming port. _x000D__x000D_Assistant Relay Normal Use M0 - M383 _x000D_ Hold After Power Off M384-M1535 _x000D_ Special Use M8000-M8255 _x000D_State Holding Use S0-S999 _x000D_Timer 100MS T0-T199 _x000D_ 10MS T200-T245 _x000D_ 1MS T246-T249 _x000D_ 100MS accumulation T250-T255 _x000D_Counter 16-bit C0-C15(0-32767) _x000D_ 16-bit(Hold After Power Off) C16-C199 _x000D_ High Speed(Hold After Power Off) C200-C255 _x000D_Data Register 16-bit D0-D127 _x000D_ 16-bit(Hold After Power Off) D128-D5029 _x000D_ 16-bit Special Use(AD) D5030(Output Voltage: 0-10V) _x000D_ 16-bit Special Use(DA) D5101(Output Voltage: 0-3.3V) 1This programmable logic controller uses industrial-grade 32-bit MCU with strong anti-interference and faster speed. 2High quality chip, stable performance, on-line download, on-line monitoring, automatic save when power off. 3Program is written in ladder logic programming language, supports for GX-Developer, GX-work2. 4Programming port is the port for program upload, download, test and monitor. 5It is reusable, stable, easy to learn. The PLC transmission baud rate is 9600.