DC5-36V Delay Relay Module LED Dual MOS Digital Delay Relay Module Trigger Cycle Timer Control Module Circuit Board

Features:_x005F_x000D_Function: 1. One click emergency stop function (STOP key). 2. Automatic shutdown: Without any operation for 5 minutes, the monitor will automatically shut down. 3. Equipped with reverse connection protection. 4. Wake up with any button. 5. Power off save: All set parameters are automatically saved after power off. 6. Different OP, CL, and LOP parameters can be set independently and saved separately._x005F_x000D_Timing range: 0.1 seconds (minimum) -999 minutes (maximum) continuously adjustable._x005F_x000D_Wide voltage operation (5-36V), widely used in controlling motors, light bulbs, LED light strips, DC motors, micro water pumps, solenoid valves and most other equipment, very convenient to use._x005F_x000D_Adopting dual MOS parallel active output, the power is strong, the internal resistance is lower, and the current is larger. It is 15A and 400W at room temperature, meeting the needs of most devices._x005F_x000D_Realize high-frequency fast and frequent on/off of the circuit, unlimited switching times, and long service life. The on/off process does not produce noise, there are no electric sparks, and there is no electromagnetic interference._x005F_x000D__x005F_x000D_Specification:_x005F_x000D_Name: Relay Modules_x005F_x000D_Working voltage: DC 5V-36V_x005F_x000D_Trigger signal source: High level trigger (CC 3.0 V-24V) signal grounding and system grounding are not common grounding to improve the system's anti-interference ability (you can also short-circuit the common grounding yourself)_x005F_x000D_Output capacity: DC 5V-36V, continuous current of 15A at room temperature, power of 400W. (Under auxiliary cooling conditions, the maximum current can reach 30A.)_x005F_x000D_Static current: 15mA_x005F_x000D_Service life: unlimited number of switches_x005F_x000D_Working temperature: -40 -85 _x005F_x000D_Size: 6.0cm x 3.4cm x 1.2cm_x005F_x000D__x005F_x000D_Working mode:_x005F_x000D__x005F_x000D_P1 mode: After the signal is triggered, the relay conducts for OP time and then disconnects; During OP time, perform the following actions_x005F_x000D_P1.1: Signal triggered again invalid_x005F_x000D_P1.2: Signal triggered again for re timing_x005F_x000D_P1.3: The signal triggers a reset again, the relay disconnects, and the timer stops;_x005F_x000D_P-2: After the trigger signal is given, the relay will disconnect for CL time, and the relay will conduct for OP time. After the timing is completed, the relay will be disconnected;_x005F_x000D_P3.1: After the trigger signal is given and the relay is turned on for OP time, the relay will disconnect for CL time, and then the above actions will be repeated. Within the cycle, the signal will be given again, the relay will disconnect, and the timer will stop; The number of cycles (LOP) can be set;_x005F_x000D_P3.2: After powering on, there is no need to trigger a signal. The relay conducts for OP time, the relay opens for CL time, and the above actions are repeated; The number of cycles (LOP) can be set;_x005F_x000D_P-4: Signal holding function. If there is a trigger signal, reset the timer and keep the relay conductive; When the signal disappears, disconnect the relay after timing OP; During the timing period, if there is a signal again, the timing will be reset to zero;_x005F_x000D__x005F_x000D_Special attention:_x005F_x000D__x005F_x000D_1. The module is an active live output, and the voltage at the output end (load end) is equal to the input voltage (DC 5V-36V)._x005F_x000D__x005F_x000D_2. The two poles of 'DC+' and load '+' are inherently short circuited internally, but the two poles of 'DC -' and load '-' cannot be short circuited during use, otherwise the load will not be controlled to turn on and off, which is equivalent to the load being constantly powered on._x005F_x000D__x005F_x000D__x005F_x000D_How to choose a timing range:_x005F_x000D_After setting the parameter values on the mode selection interface, press the STOP key briefly to select the timing range;_x005F_x000D_XXX Decimal point in units, timing range: 1 second to 999 seconds_x005F_x000D_XX X decimal point to ten places, timing range: 0.1 seconds to 99.9 seconds_x005F_x000D_X. X.X. All decimal points are on, timing range: 1 minute to 999 minutes_x005F_x000D_For example, if you want to set OP to 3.2 seconds, then move the decimal point to ten places and the digital display will show 03.2_x005F_x000D_Parameter Description: OP conduction time, CL disconnection time, LOP cycle count (1-999 times, "---" represents infinite cycles)_x005F_x000D_These parameters are independent of each other, but they are shared by various modes. For example, if the conduction time OP is set to 5 seconds in P1.1 and the user wants to switch to P1.2 mode, then when entering P1.2 to set the corresponding parameters, the OP will also be 5 seconds;_x005F_x000D_Short press the SET key on the main interface (displaying 000) to display OP (CL, LOP) and corresponding time XXX;_x