Item Type:DC Permanent Magnet Motor_x000D_ Item Type:DC Permanent Magnet Motor_x000D_ Model: 31ZY_x000D_ Type: Permanent Magnet DC Motor_x000D_ Rated Voltage: 6-24 (V)_x000D_ Parameters: (Corresponding to the Table Below According to the Title Speed) Using Voltage V_x000D_ _x000D_ Operating Voltage (V)6V12V12V24V24V24V_x000D_ No Load Current (mA)18011035040100200_x000D_ No Load Speed (rpm)400040008000350050008000_x000D_ Rated Torsion (g.cm)100100200120200200_x000D_ Rated Speed (rpm)320032006500290840006600_x000D_ Rated Current (A)0.80.51.62.30.61.0_x000D_ Locked Rotor Torsion (g.cm)50060010006698501200_x000D_ Locked Rotor Current (A)3.32.36.51.062.04.4_x000D_ CCM2 DC Motor Speed Regulator Product Output_x000D_ DC Motor Regulator CW CCW Control_x000D_ This governor uses PWM speed control technology, which has the characteristics of high conversion efficiency, wide speed range and stable performance. All use imported STMicroelectronics original chips, which have been tested for voltage, current, function, etc. before leaving the factory, and the circuit is stable and reliable._x000D_ Technical Parameter:_x000D_ Model: CCM2_x000D_ Working Voltage: DC10V-30V_x000D_ Control Power: 12V x 3A=36W, 24V x 3A=72W Greater than 24V, Maximum 120W_x000D_ Rated Current: 3A_x000D_ Maximum Current: 5A_x000D_ PWM Pulse Width Adjustment System Range: 5%-95%_x000D_ Potentiometer: Resistance Value B10K, Wire Length 20CM, Opening 8mm,_x000D_ Output Voltage: About 0-100% of the Input Voltage_x000D_ Speed Governor Size: Approx. 74 x 47 x 28mm / 3 x 2 x 1.1in_x000D_ Potentiometer is used for speed regulation_x000D_ CW CCW switches are used to control CW, CCW, and stop_x000D_ Note:_x000D_ Motor_x000D_ 1. When you use the motor, there should be no binding objects. For example, the adhesive should not flow into the bearing through the rotating shaft, which will hinder the operation of the motor._x000D_ 2. The rotation of the shaft may have the opposite effect on the life of the motor. In order to prolong the life, please check whether your load is in accordance with the regulations. Do not overload or have objects that hinder rotation at the end of the shaft._x000D_ 3. Manufactured into an eccentric heavy radiation load, which is harmful to the life of the motor._x000D_ 4. Do not store in surrounding high temperature or extreme humidity, and do not place in corrosive gas, which will reduce the effect of the motor._x000D_ 5. Do not run the motor in the surrounding high temperature and humidity._x000D_ 6. When soldering is needed on the positive and negative motor terminals of the power supply, the temperature of the soldering iron is 34040, and the heating time is within 3 seconds. Do not deform the plastic. Let the soldering spot flow into the motor or break the end of the wire during work. Motor function declines._x000D_ 7. Do not let the motor shaft get stuck. When the power is supplied, the motor will overheat in a short time and its accessories will be burnt._x000D_ 8. Due to the lack of skills of the staff, the quality of the motor cannot be guaranteed when it encounters the things mentioned in the manual, or the superficial judgment is obviously fault._x000D_ 9. Supply the specified power and be sure that it is within the range of measurable requirements._x000D_ 10. The installation of pulleys or gears should not be abnormally aggravated when pressed in._x000D_ 11. When installing the motor, if the screw is too long, it will cause contact between the motor itself and the rotor, which will affect the characteristics._x000D_ _x000D_ Governor_x000D_ 1. The input of the DC motor speed controller is DC, and it cannot be directly connected to AC (such as household 220V AC motors), otherwise it will burn out._x000D_ 2. The positive and negative poles of the DC power supply cannot be reversed, otherwise the governor will be damaged._x000D_ 3. The motor can be positive or negative. When the running direction is inconsistent with the expectation, the direction can be changed by adjusting the wire sequence._x000D_ 4. The potentiometer knob can change the duty cycle of the governor output, thereby changing the motor speed