AC 110V 220V DC 12V Digital Time Delay Relay LED Display Cycle Timer Control Switch Adjustable Timing Relay Time Delay Switch

Specifications: Timing range: 0-999s,0-999m,0-999h Power supply voltage: DC12V /AC 110V 220V Relay: 20A Working current: 10A(maximum) Power: 1500W (maximum) Size: 79 x 26 x 43mm/2.99" x 1.02" x 1.69" Hole size: 72 x 40mm/2.83" x 1.57" Instruction Manual: 1.After setting the data, you must wait 6 seconds,6s post modules automatically save memory set data. 2.Press SET key once to enter the time setting mode,the red LED flashes, press the key to increase or decrease the setting time T1. 3.After setting time T1,short press the SET key again, the green LED flashes,and the time is set by pressing the key Time T2, T2 time setting is completed,press SET key again, the system will automatically save the memory setting time or wait for 6s, 6s module will automatically save the data memory. 4.Long press SET,enter parameter setting mode.There are two sets of parameters for the user to select P0, P1.Short press SET in the current mode to switch between P0 and P1. 5.In P0 parameter can be set by pressing the key to adjust their own timing mode.In the P1 parameter can be set by adding and subtracting keys work mode. P0--0:T1 Timing mode is second. P0-1: T1 timing mode is minutes. P0--2:T1 Timing Time mode is hour. P1--0:Delay T1 time,relay pull(T1 timer) P1--1:Relay release after T1 time delay (T1 timer) P1--2:Delay T1 time,relay pull(T1 timer),and then relay release after T2 time delay(T2 timing),then it is finished. P1--3:Relay release after T1 time delay(T1 timer),then delay T2 time,relay pull(T2 timing),then it is finished. P1--4:Delay T1 time,relay pull(T1 timer),and then relay release after T2 time delay(T2 timer),cycling. P1--5: Relay release after T1 time delay(T1 timer),then delay T2 time,relay pull(T2 timer),cycling. Package Included: 1 x Dual Display Time Delay Relay Working voltage=voltage indicated on the label S1 and S2 have no output Reminder When the label indicates voltage=load working voltage The time controller can share the power supply with the load Common AC power supply Common DC power supply Code parameter setting 1. Enter the code parameter setting interface Press and hold the "S key for 6 seconds to enter the code parameter setting interface 2ClickorAdjust parameter value 3. Click the "S" key to switch the code, and continue to click to exit the setting 3P0 code parameter meaning: timing unit P0=0 Unit=seconds (default) P0=1 Unit=minutes P0=2 Unit=Hour 4P1 code parameter meaning: working mode P1=0=Start regularly Power off the load first The load remains energized at the end of the time P1=1= Scheduled shutdown Power on the load first End of time, keep the load powered off and shut down P1=2=Alternating switch The load is powered on and then powered off alternately once End of time, keep the load powered off and shut down P1=3=Alternate closing and opening The load is powered off and then powered on alternately once The load remains energized at the end of the time P1=4=Cycle Off The load is powered off before being powered on Infinite loop P1=5= Cycle switch Load is powered on before power off Infinite loop Timing parameter setting 1. Enter the code parameter setting interface Double-click the S key to enter the code timing parameter setting interface 2ClickorAdjust parameter value 3. Click the "S" key to switch the code, and continue to click to exit the setting Resume by Alarm 1. Delayed startup means that the power is cut off first and then kept on. It is assumed that the startup needs to be delayed for 6 seconds. Then the code parameter is set to P0=0; P1=0, set the timing parameter PV nixie tube to 6, and SV ignores the setting. Scheduled shutdown setting 1. Delayed shutdown means power-on and then power-off. It is assumed that the shutdown needs to be delayed for 6 seconds. Then the code parameter is set to P0=0; P1=1, set the timing parameter PV nixie tube to 6, and SV ignores the setting. Alternate switch 1 time setting Power off first and then power on alternately for 1 time, and then keep power off without cycling Suppose you need to shut down for 100 seconds, then turn on for 50 seconds, and finally shut down. Then the code parameter is set to P0=0; P1=2, set the timing parameter PV nixie tube to 100 and SV nixie tube to 50. Power on first and then power off alternately once, and then keep power on without cycling Suppose you need to turn on the machine for 100 seconds, then turn off the machine for 50 seconds, and finally turn on the machine. Then the code parameter is set to P0=0; P1=3, set the timing parameter PV nixie tube to 100 and SV nixie tube to 50. Infinite cycle switch setting Power off before power on infinite cycle Suppose you need to shut down for 100 seconds, then start up for 50 seconds,