3D Printer Auto Adjustment Bed Leveling Sensor TR Sensor Auto Glass Bed Level

₹2,299.00
+ ₹168.99 शिपिंग

3D Printer Auto Adjustment Bed Leveling Sensor TR Sensor Auto Glass Bed Level

  • ब्रांड: Unbranded

3D Printer Auto Adjustment Bed Leveling Sensor TR Sensor Auto Glass Bed Level

  • ब्रांड: Unbranded
RRP: ₹3,249.00
मूल्य: ₹2,299.00
आपकी बचत: ₹950.00 (29%)
द्वारा बेचा गया:
₹2,299.00
+ ₹168.99 शिपिंग

स्टॉक में है

हम निम्नलिखित भुगतान विधियाँ स्वीकार करते हैं

विवरण

TR Sensor is an auto leveling sensor for 3D Printers that can precisely measure the tilt of your print surface. It can greatly improve the printing bed of your 3D Printer. TR Sensor features simple, smart and precise. It could work with nearly any kind of bed materials, such as woods, metals, and so on. Especially for black lattice glass. 1, Innovative Solenoid: Ultra Power Saving On idle state, while the push-pin is whether pulled out or retracted, there are not any electric current flowing on solenoid, and standby electric current in the whole device is below 15mA on average, whereas on working state, while the pin is moving in sudden about 100ms, under 300mA flows in the device. Low power consumption even further drops joule heating, preventing from heat problem. 2, wide Selection of Bed TR Sensor does not uses either optical, nor proximity (inductive/capacitive) sensor. TR Sensor is controlled by Hall Effect, providing high precision. Thus the bed material can be selected freely. 3, Optimized structure: Larger Build Size TR Sensor is a small and technology-intensive one. Build size can be set larger than other existing auto bed leveling sensor. TR Sensor uses existing RC Servo motor signal intactly, so just plug 3DTouch on the same pins after removing servo motor. Specifications: Installation: 2pc M3 15mm Screws Voltage: 6V ~ 38V Cable length: 120mm Net Weight: 60g Auto leveling sensor installation height: 2mm higher than the nozzle Wiring 3-pin: Blue (-, GND), Brown (+5V), Black (control signal) Caution Additional power supply will be needed in case your board does not supply enough amperage. Electronic devices can be damaged or even destroyed if connected to wrong polarity. [wrong terminal connect to 5V(+) and GND(-)] Please note that: If your 3D Printer is not Tronxy, you will need to do some modification to your firmware and for some control board, you may need to do some soldering work to the connector. Package list 1 TR Sensor with 120mm Cable
  • Fruugo ID: 328022480-724678353
  • EAN: 9463280283081

उत्पाद सुरक्षा जानकारी

कृपया नीचे दी गई इस उत्पाद से संबंधित विशिष्ट उत्पाद सुरक्षा जानकारी देखें

निम्नलिखित जानकारी इस उत्पाद को बेचने वाले स्वतंत्र तृतीय-पक्ष खुदरा विक्रेता द्वारा प्रदान की गई है।

उत्पाद सुरक्षा लेबल

CE Mark
सुरक्षा चेतावनियाँ: Please pay attention to the instructions before use

डिलीवरी और वापसी

24 घंटों के भीतर भेजा जाएगा

  • STANDARD: ₹168.99 - के बीच वितरण गुरु 04 दिसंबर 2025–गुरु 11 दिसंबर 2025

चीन से शिप हो रहा है।

हम आपके द्वारा ऑर्डर किए गए उत्पादों को पूरी तरह से और आपके विनिर्देशों के अनुसार डिलीवर करने की पूरी कोशिश करते हैं। हालाँकि, यदि आपको अधूरा ऑर्डर या आपके ऑर्डर से कोई अलग आइटम प्राप्त होता है या किसी अन्य कारण से यदि आप अपने ऑर्डर से संतुष्ट नहीं हैं तो आप ऑर्डर या ऑर्डर में शामिल कोई भी उत्पाद वापस कर सकते हैं और आइटम के लिए पूर्ण रिफ़ंड प्राप्त कर सकते हैं। सम्पूर्ण वापसी पॉलिसी दिखाएँ

उत्पाद अनुपालन विवरण

कृपया नीचे दी गई इस उत्पाद से संबंधित विशिष्ट अनुपालन जानकारी देखें।

निम्नलिखित जानकारी इस उत्पाद को बेचने वाले स्वतंत्र तृतीय-पक्ष खुदरा विक्रेता द्वारा प्रदान की गई है।

निर्माता:
नीचे Fruugo पर बिक्री किए जाने वाले संबंधित उत्पाद निर्माता के संपर्क विवरण की जानकारी संबधी सूचना है।

  • Ebeis(HK) co., Limited
  • Ebeis(HK) co., Limited
  • Flat/RM 185G/Fhang Wai lnd Centre
  • No.6 Kin Tai ST, Tuen Mun, NT
  • Hongkong
  • HK
  • 999077
  • ebeishk@hotmail.com

यूरोपीय संघ(EU) में जिम्‍मेदार व्यक्ति:
नीचे यूरोपीय संघ में जिम्मेदार व्यक्ति की संपर्क जानकारी संबंधी सूचना है। जिम्मेदार व्यक्ति यूरोपीय संघ में स्थित पदनामित आर्थिक ऑपरेटर है जो यूरोपीय संघ में बिक्री किए जाने वाले संबंधित उत्पाद संबंधी अनुपालन दायित्वों के लिए जिम्मेदार है।

  • Yuan Li
  • Sea&Mew Consulting GmbH
  • Mittenhuber Stra?e 4
  • Neumarkt
  • DE
  • 92318
  • Compliance.EU@outlook.com
  • 4915224685061