["Feature:\r\n1.Support Lead-acid battery and Acting Battery,voltage range:6V~60V;\r\n2.Can display voltage,percent of battery,charging for time at the same for time through LCD\r\n3.The function is very powerful,realizes the automatic charge control,the control charge for time, also may set up and uploads the corresponding parameter through the serial port\r\n\r\nSpecifications:\r\nProduct Model:XY-L30A\r\nControl voltage:DC6-60V\r\nControl current:<30A\r\nControl accuracy:0.1V\r\nOutput Type: Direct Output\r\nVoltage error:±0.1V\r\nScope of application: various lithium batteries\r\n一.Function description\r\n1.Automatic Charge control function：\r\nBy setting the volt-HI:‘UP’ volt-LI:‘dn’;When the battery voltage is below the volt-LI:’dn’,the relay leads,the charger begins to charge the battery;when the battery voltage is up to volt-HI:’UP’,the relay is diconnected and the automatic charge is completed once\r\n2.Charge for Time Control Function:\r\nHow to turn on the for time control function?\r\nAfter entering the parameter set, set the parameter op is non-zero, then turn on the for time control function, op default parameter is:--:--h, the default does not turn on for time control function;\r\nAfter the opening for Time control function (OP is non-zero), when the battery voltage is the lower volt-LI’dn’, the charger began to charge the battery, the system began to clock; During the timing, the battery voltage ≥ volt-HI’UP’, relay disconnect; If the OP for time is up, the battery voltage is still the lower volt-LI’dn’, the relay keeps the conduction, automatically closes the charge for time control function, and flashes the H:ER to remind the user, the for time parameter setting is unreasonable; Press any for key to stop flashing;\r\nNote: for Time format: 00:59 (00 for hours, 59 for minutes) The maximum for time is 99:59, which is 100 hours.\r\n二.Parameter Setting\r\na)Press and hold the SET for key to enter the setting interface;\r\nb)Switch the parameters you want to set by short press SET;\r\nc)After the selection of parameters, can be set by the UP/DOWN for key to support the short press, long press (fast increase or decrease); To set other parameters, repeat step b, c);\r\nd)After all parameters are set, long press set for key to exit and save;\r\n三.The for Key Function Description:\r\nIn the Run interface (main interface):\r\nShort press SET button to display the current set of parameters; Short press UP button, toggle display charge percentage and charging for time;\r\nShort Press DOWN button, select Turn on/off relay enabling, if the relay can be closed, will show ' off ' as a reminder;\r\nLong press UP button, switch low power state\r\non：No operation in 10 minutes turn off backlight\r\nOFF: Backlight is for always bright\r\nLong press SET button,enter the parameter settings.\r\n四.Calculation of voltage percentage：\r\nvoltage percentage = battery voltage/(volt-HI – volt-LI)\r\n五、Additional Features\r\na)Charging for time recording function: not open charging for time control, the product will record a full for time, when the entry for time display interface, flashing display charging for time, and then exit for time display interface or next charge to open (relay conduction) when empty;\r\nb)Automatic parameter detection: When the parameters are set, exit, if volt-LI dn≥ volt-HI UP, the system will flash display \"ERR\" as a reminder;\r\nc)Battery Access detection: This product attached to the battery, if not connected to the battery, the system will be shown in the downlink \"NbE\" as a reminder\r\nSize:9.2x4.5cm/3.62x1.77inch\r\nNote:\r\nPlease allow 1-3mm error due to manual measurement.pls make sure you do not mind before you bid.\r\nDue to the difference between different monitors,the picture may not reflect the actual color of the item.Thank you!\r\n\r\nPackage Includes:\r\n1x Battery Charger Control Module"]