Features: _x000D_ 16 opto isolated digital inputs,3 opto isolated digital outputs; _x000D_ Upgrade algorithm,support soft interpolation,fixed arc interpolation bug of the old version; _x000D_ Analog spindle control 0-10V spindle control (can be modified as PWM output); _x000D_ Interface clear and simple, powerful, almost meet all requirements _x000D_ There is a key emergency STOP function (STOP key), with reverse connection protection, reverse connection does not burn _x000D_ Added sleep mode, after enabling, 5 minutes without any operation, automatically close the display, any button to wake up _x000D_ Different OP, CL and LOP parameters can be set, which are independent and saved separately _x000D_ Set parameters for automatic power off and save _x000D_ With optocoupler isolation, enhance anti-interference ability, industrial level circuit board, set parameters after power off forever memory _x000D_ _x000D_ _x000D_ Specification: _x000D_ 2: Trigger Source: Active-high (3.0V-24V), have optocoupler isolation, can improve the system's anti-jamming capability (customers can also shorting common ground). _x000D_ Output capacity: 5V--36V DC, 15A continuous current at room temperature, 400W power (maximum current up to 30A under auxiliary cooling conditions) _x000D_ Service life: infinite times switch _x000D_ Working temperature: - 40~85 _x000D_ Weight: Approx.16g/0.6oz_x000D_ _x000D_ Operating mode:_x000D_ P1: trigger signal, the relay is on "OP" time, and then disconnect; in the "OP" time, as follows:_x000D_ P1.1: signal is triggered again, invalid_x000D_ P1.2: signal is triggered again, the clock is reset_x000D_ P1.3: Signal trigger again, relay off, stop the clock;_x000D_ P-2: trigger signal, the relay off "CL" of time, the relay on "OP" time, and then disconnect relay;_x000D_ P3.1: trigger signal, the relay is turned on after the "OP" time, the relay off "CL" time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( "LOP ") can be set._x000D_ P3.2: without triggering signal, the relay is on "OP" time, the relay off "CL" time, and has been cycling; frequency ( "LOP") cycle can be set;_x000D_ P-4: signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing "OP" time, the relay is; if another signal during timing, timing is cleared; _x000D_ _x000D_ _x000D_ Pay attention:_x000D_ 1. The module is an active output, the output voltage equal to the input voltage._x000D_ 2.'DC + 'and' load + 'This is an internal short circuit of the poles, but' DC- 'and' load - 'poles during use can not be shorted, otherwise the load can not be controlled on and off, which is equivalent load is been carrying electricity. _x000D_ _x000D_ _x000D_ Timing range:_x000D_ How to choose the time range?_x000D_ After setting the mode selection screen parameter value by a short press "STOP" button to select the time range;_x000D_ XXX. decimal point in the unit place, time range: 1 second to 999 seconds._x000D_ XX. X decimal point in decade place, Timing range: 0.1 seconds to 99.9 seconds_x000D_ X. X. X. decimal full brightness, Timing range: 1 minute to 999 minutes._x000D_ For example, you want to set "OP" is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2_x000D_ Parameter description: "OP" - conduction time, "CL" - off time, "LOP" - the number of cycles (1-999 times, "---" represents infinite loop)._x000D_ These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time "OP" is 5 seconds, if you switch to P1.2 mode, it's "OP" will be 5 seconds too._x000D_ In the main interface (display 000), short press "SET" button will display "OP" ( "CL", "LOP") and the corresponding time XXX;_x000D_ Some parameters only mode "OP" (such as the mode P1.1, P1.2, P1.3), short press the "SET" key to display only the "OP"and the corresponding time;_x000D_ Some models have parameters "OP", "CL", "LOP" (such as the mode P3.1, P3.2), short press "SET" button will display "OP" and the corresponding time, "CL" and the corresponding time, "LOP" and the corresponding number of times;_x000D_ In the main interface by short press "SET" key to see information about the parameters of the current mode, very convenient! _x000D_ _x000D_ _x000D_ How to set parameters?_x000D_ 1. First, read the instructions to determine the required operating mode._x000D_ 2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press "SET" button for 2 seconds after release to enter mode selection interface; a short time by pressing "UP", "DOWN" key to select the mode (P1.1 ~ P-4)._x000D_ 3. Select the mode (such as P3.2), short press the "SET" button, t